Outdoor WirelessDigital Bridge/CPE  Quick Setup Wizard

V1.0

Hardware connection schematic diagram

5G Bridge

Interface Descriptions

DIP Switch:To adjust the transformation between the “Master AP” mode

and the “Subordinate AP” mode of the bridge.(M)(S)

DC:Power interface,12V 1A DC power interface.

Digital Switch/Reset:Both digital switch and reset button,short press the

button when electrifying,the numeric value of the digital tube will be added

one and press15 seconds, the device will be restored to the factory setting.

(Dig SW/Reset)

2G Bridge

LAN1/POE:This is a data transmission port, and it is also a power port.When

the device works in the bridge mode, the interface acts as a LAN port function.

When the device works in the route mode, the interface acts as a WAN port

function.This interface is used to connect the POE interface to the POE

power.

LAN2:This is a LAN data transmission port which can connect computers,

cameras, switches and other devices.

5G Bridge

ETH/POE interface:This is a data transmission port, and it is also a power

port.When the device works in the bridge mode, the interface acts as a LAN

port function.When the device works in the route mode, the interface acts

as a WAN port function.This interface is used to connect the POE interface

to the POE power.

COM:It is a debugging interface.

Indicator light state description

Fast pairing of digital switch

One to one pairing method

1.Dial a bridge to “M” and the another bridge to “S”.

2.Short press “Dig SW / Reset” button, each digital tube value will

add one (0-9-A-F cycle).

3. The paired bridge is set to the same value and can be paired successfully.

One to multiple pairing method

1.Dial a bridge to “M” and the another bridges to “S”.

2.Short press “Dig SW / Reset” button, each digital tube value will

add one (0-9-A-F cycle).

3. The paired bridge is set to the same value and can be paired successfully.

Digital tube and wireless channel comparison table

Note:

1.The default channel bandwidth of the wireless bridge is 40MHz.

2.The number of channels supported by some wireless bridges will vary .

Please refer to the actual product.

Setting up a bridge in a browser

1)Open the computer--Right click【Internet】-【Attribute】-【Change adapter

settings】;

2)Right click of the mouse click 【Local connection】,Select 【Attribute】;

3)Double-click the 【Internet protocol version 4 (TCP/IPv4)】in the connection

properties dialog box project(as show in the left below).

4)In the 【Internet protocol version 4】 dialog box, choose 【use the following

IP address】 and set the IP address to 169.254.254.X (X is any number

between 1-253), and the subnet mask is set to 255.0.0.0 (as show in the

right below). Finally,click 【OK】 and quit.

Login management interface

The default mode of the device is the bridge mode,open the computer

browsers, after entering its address 169.254.254.254, the bridge device

list will be displayed,and clicks on the【 login 】button to log in to the device.

Note:Some wireless bridges do not have “Bridege Device List” function. Please

refer to the actual product for details.

The username and password of the web management platform are all admin，

click the 【 login 】 button to log in to the device.

Network settings

Configuring the mode and bridge interface according to the network usage

of the site. 【 Bridge mode 】 refers to the wireless transmission of data by

the device. 【 Route mode 】 refers to the device's NAT conversion and wireless

transmission of the data.

Description:The device supports bridge mode and route mode in the “M

AP” mode,but only support the bridge mode in the “S AP” mode.

Wifi settings

Note: Some wireless bridges do not have this function. Please refer to the actual

product for details.

The default WiFi name of the 2G Bridge is Brap-2G-XXXX,the password

is 88888888.

The default WiFi name of the 5G Bridge is Brap-5G-XXXX,the password

is 88888888.

Computers, mobile phones, and other terminals can be wirelessly

connected to the device through this signal.(Remarks:XXXX is the last

four bits of the bridge's MAC address)

Description:The device launches the WiFi signal in the main AP mode.In

the secondary AP mode, the WiFi signal is transmitted only after the bridge

pairing is successfully connected.

Bound cloud end

Note: Some wireless bridges do not have this function. Please refer to the actual

product for details.

If the device is connected to the Internet,you can configure the 【bridge interface】

information.After the device is connected to the Internet, it can be remotely

managed by the cloud.

1.Login “www.tianwifi.net”.net to apply for a cloud account.

2.Fill in your cloud account in the "username" column.

3.The server address bar is filled in “www.tianwifi.net”.

4.The device description bar suggests filling up the installation location for later

management.

5.Click the 【Save】 button, prompting the connection state: Connected to

www.tianwifi.net, which indicates that the device has successfully bound the

cloud platform.

Cloud management

1.Login cloud platform:www.tianwifi.net.

2.Click on【 Area list 】--【 Management 】--【 Device management 】,find the

binding bridge, click[Remote management ] buttton and you can remote

login management.

PS:Cloud management only supports remote configuration of devices.There

is no limit to the number of cloud bound devices.But it does not support

authentication, data statistics, and business functions.